Category: Main > Commercial - Dealer Only > Rotators

EMOTATOR 1103MSXB Refurbished & Upgraded Rotator  - $1,200 Listing ID: 27590

Classified Info

Listing Began: Dec 2 16:30
Number of Times Viewed: 14
  • 2020-10-001a.jpg
  • 2020-10-002.jpg
  • 2020-10-003.jpg
  • 2020-10-005.jpg
  • 2020-10-006.jpg
  • 2020-10-007.jpg
  • 2020-10-008.jpg
  • 2020-10-009.jpg
  • 2020-10-015.jpg
  • 2020-10-019.jpg
  • 2020-10-019c.jpg
  • 2020-10-011.jpg
  • 2020-10-013.jpg
  • 2020-10-021.jpg
  • 2020-10-025.jpg
  • 2020-10-026.jpg
  • 2020-10-027.jpg
  • 2020-10-028.jpg
  • 2020-10-017.jpg
  • 2020-10-018.jpg



Seller's Comments and Description:

Rotator with Standard Full Circle Controller, Refurbished & Upgraded.

Includes Top Mast Clamp, Plugs For Control Cable & IEC power lead + revised manual.


Wind Area ................2.5m Sq.

Rotation Torque ..... 10.0 Kg/m

Brake Torque ......... 100 Kg/m

Mast Size ................ 40 ~ 62mm

Rotation Time ........ 110 second 360 degree

Rotator Voltage ..... 100vAC

Rotator Weight........8.0Kg.


The MSXB Controller:-  Full circle display with momentary & lift to lock direction switch.

Also includes my BDS35 Auto brake release & delay PCB, which has 3 or 5 second delay. Controlled by the direction switch, all in one action no extra switches to control the brake.

Disassembled, cleaned & prep chassis for upgrades & new parts.

On the front panel:- Installed a 3mm red LED for brake action, controller by the BDS-35 PCB.

The Back Panel:- Installed a new 8 pin Cinch socket & laser cut S/S cover/mounting plate, New fused IEC 240v socket & earth bolt.

On The Inside:- Upgraded the display illumination with 2 x 3 LED modules & there power supply.

Installed a new 100vAC output Australian made transformer which supplies power to the display transformer + direction & brake actions. Also installed the BDS-35 PCB & fully rewired. 

Refurbished the display POT & installed a new display drive belt.

Re-assembled, fully tested & aligned with the 1103 rotator.


The 1103 Rotator :- Has solenoid activated twin wedge brake system.

Disassembled to the last nut, bolt & screw. Cleaned & checked all parts for damage.

Main housing bearing tracks have been re-ground & polished, as they had some damage. This process change the bearing size from 9.5mm up to 10mm, now there is very little end float or side movement. 

The 4th gear in the drive train was replaced with a new thicker Stainless Steel version, as the original version is a weak point of these rotators. This new gear S/S gear was made for me by ASM Services, they manufactured it using Laser Sintering 3D Printing process. This replacement is nilly double the thickness of the original gear.

All housing & the mast bracket have been Glass Bead Blasted by IMPACT GLASS BEAD followed by Etch priming & finished off in Pewter epoxy enamel paint.

Replaced the original (hard to get) control cable plug/socket with Amphenol LTW IP67 7 pin plug & socket, the new socket was mounted on a new Stainless Steel  mounting plate..

The gears were aligned & shimmed then re-assembled into the refurbished housings with new bearings & new grease through out.

Re-aligned & calibrated with the MSXB controller.

240v AC, 24 month warranty.

This unit is available for exchange. Go to my web site for information.

Contact Peter on 0427 043 054 NO SMS, or via the embeded email services provided by VK Classifieds


Manufacturer Emotator
Model 1103MSXB
Condition of Item Excellent
Accessories Included Top Mast clamp assembly, IEC power lead, Plugs for control cable, revised manual
Postage / Freight Pickup Available


<< Previous Next >>