Category: Main > Commercial - Dealer Only > Rotators

DAIWA DR-7600 rotator with a choice of controllers  - $600 Listing ID: 16524



Classified Info

Listing Began: Dec 3 13:10
Number of Times Viewed: 114
  • 02-12-003a.jpg
  • 02-12-001a.jpg
  • 02-12-004a.jpg
  • 02-12-005a.jpg
  • 02-12-010a.jpg
  • 02-12-009a.jpg
  • 03-12-002.jpg
  • 03-12-003.jpg
  • 03-12-005.jpg
  • 03-12-007.jpg
  • 07-05-032.jpg
  • 07-05-034.jpg
  • 07-05-039.jpg
  • 07-05-042.jpg
  • 22-09-002a.jpg
  • 22-09-003a.jpg
  • 22-09-005a.jpg
  • 01-10-017T.JPG
  • 04-12-012a.JPG
  • 25-11-014a.jpg

Videos


Options

  • $75

Description

Seller's Comments and Description:

Refurbished & upgraded rotator & controller.
The DR-7600 Rotator:- (Same as Kenpro KR-600). Fully stripped down & cleaned etc. The (4 stack loose) final drive gears has been replaced with a solid one piece version (KD-38T), this gives more contact area onto the rare ring gear. Refurbished the POT, replaced the limit switches, installed a new round 7 pin IP67 socket mounted on a S/S cover plate. The housings & mast clamps were glass bead blasted then etch primied followed by painting in Epoxy Gloss Enamel Pewter. Reassembled with new ball bearing & new grease through out. Aligned & calibrated to the controller of you choice.
Supplied with 7 pin IP67 plug & S/S mounting/clamping hardware.
SPECS.
Antenna wind area...................1.5 mSq.
Rotation Torque........................6.0 Kg/m
Brake Torque............................40 Kg/m
Brake system...........................Drum & coil drag spring ontop of motor.
Limit end stops.........................Mechanical & electrical
Rotation time...........................60 seconds
Control cable...........................6 core
Mast Size................................38 ~ 63 mm
Rotator voltage........................24v AC
THE CHOICE OF CONTROLLERS:-
(1) The DC-7011:- Standard manual controller. Refurbished & upgraded etc.
Fully stripped down & cleaned, refurbished the POT, added LED display illumination & installed there power supply PCB, Replaced the alignment POT with a 10 turn version, replaced AC fuse clips with a fully sealed safety fuse holder, replace the flat blade screw of the output terminal with S/S phillips, replaced the power plug with an approved safety side entry version.
(2) The DC-7001d :- Standard manual controller. Refurbished & upgraded etc.
Fully stripped down & cleaned, refurbished & repaired POT + display gear train, install illuminated push button switches for direction & power, installed LED display illumination & installed there power supply onto the main PCB, Replaced the alignment POT with a 10 turn version, Install a fused IEC power socket to the rear panel also installed earth bolts, the output terminal board was stripped cleaned & had the screw terminals replaced with later versions. The housing were glass bead blasted the under coated followed by painting in epoxy enamel hammer tone grey.
Supplied with IEC power lead.
(3) The DC-7004 :- Manual & Dial Pre-Set controller. Refurbished & upgraded etc.
Completely disassembled cleaned, upgraded & moded to work with late version rotators with the motor start CAP in the rotator.
 The top & bottom housing were glass bead blasted then primed followed by painting in  black with a full coats of clear added. Refurbished & repaired POT + display gear train, installed LED display illumination & installed there power supply onto the main PCB, Also replaced the two alignment preset POTS with 10 turn versions, The compass display was also changed. Install a fused IEC power socket to the rear panel also installed earth bolts, the output terminal board was stripped cleaned & had the screw terminals replaced with later versions.
Supplied with IEC power lead. 
Contact Peter of DUORO Services on 0427 043 054.


Details

Manufacturer Dawia
Model DR-7600 :- DC-7001d, DC-7004 & DC-7011
Condition of Item Excellent
Accessories Included Top mast clamp & plug for control cable
Postage / Freight Pickup Available





Advertisement

Next >>