Category: Main > Commercial - Dealer Only > Rotators

CDE HAM 2 Rotator & Controller  - $650 Listing ID: 15846

Classified Info

Listing Began: Jun 1 4:24
Number of Times Viewed: 1050
  • 20-09-001a.jpg
  • 20-09-002a.jpg
  • 20-09-003a.jpg
  • 20-09-004a.jpg
  • 20-09-005a.jpg
  • 20-09-007a.jpg
  • 20-09-008a.jpg
  • 20-09-009a.jpg
  • 20-09-010a.jpg
  • 20-09-011a.jpg
  • 20-09-012a.jpg
  • 20-09-017a.jpg
  • 20-09-018a.jpg
  • 20-09-022a.jpg
  • 20-09-026a.jpg
  • 20-09-027a.jpg



  • $70


Seller's Comments and Description:

CDE HAM2 Rotator & Controller; Refurbished & Upgraded with 12 month warranty.
Includes;- Top mast clamp & hardware, plugs for control cable, IEC power lead + revised manual.
12month warranty extenable to 24month for an extra $100.00

Wind Area.....................1.6m Sq.
Rotation Torque............No spec available probably about 9.0 Kg/m.
Brake Torque................No specs available probably about 50.0 Kg/m.
Mast Size......................50mm dia.
Rotation Time...............60 sec for 360 degrees.
Rotator voltage.............24v AC.
Control Input voltage....240v AC.

The HAM2 Controller:- Refurbished & upgraded to dual action direction switches (No more holding down a brake switch + the direction switch) + upgraded to 7 core control cable.
Conpletely disassembled for mods & upgrades including removing the rear panel.

New BDS-35 Auto brake release & delay PCB, Convertedfrom 3 lever action to dual action two lever including new micro switches, Replaced the rear panel with a laser cut & etched stainless steel panel with provision for the New fused IEC & Cinch sockets+ new CAL/NORM switch & earth bolt, Added a LED modual for meter illimination & installed there power supply on the main PCB, Replaced the original paper direction display with a aluminium version from a Kenpro (much nicer), Added 3 LED'sfor brake & direction action, Replaced the two 220vAC transformer with a single 240Vac Australian made version with 2 seconday outputs, New illuminated power switch & CAL POT.

Fully re-wired, aligned & calibrated to the rotator.
includes IEC power lead & Cinch plug for the control cable.

The HAM2 Rotator:- Has been upgraded with a friction brake in the motor + it has a soleniod brake wedge system. 

This rotator was rebuilt with New & re-zinc plated parts(inc. top housing & brake chassis, S/S mast clamp bracket & hardware, Top gear plate,CAP, POT gearing, Bearing & retainers, Cinch socket & mounting plate + plug, Hardware etc.
The motor was stripped down & the friction was upgraded + had the cork pads replaced.
The solenoid brake assembley is in good condition.
UPGRADES:- Control cable is now 7 core (instead of 8) by way of moving the motor start CAP to the rotator savin two wires (Piins 4 & 8), I then seperated the motor & solenoid 0v on pin 1 moving the motor's 0v to too pin 4.
Installed NEW direction POT, Replaced screw terminal with a Cinch socket & cover plate, Mounted the motor start CAP, Added a (protection/safety) micro switch on the motors 0v which is activated by the wedge latch (if the brake wedge does not release the motor will not go), Mast bracket upgraded to my NEW stainless steel version with new S/S u-bolts etc.
Housings were glass bead blasted, etched primed then finished in grey enamel paint.
Shimmed & aligned the gearing, replaced the bearings & retainers, the reassembled with new grease through out.
Fully re-wired, Aligned & calibrated to the controller.
Includes top mast bracket hardwarew & Cinch plug for the control cable.
12month warranty extenable to 24month for an extra $100.00
Contact Peter of DUORO SERVICE on 0427 053 054


Manufacturer CDE
Model HAM2
Condition of Item Excellent
Accessories Included Top mast clamp & hardware, Plugs for control cable, IEC power lead + revised manual
Postage / Freight Pickup Available


<< Previous Next >>